Selection GuideThere is no uniform percentage deviating from the specific model and test conditions. Gear pumps, diaphragm pumps, and pressure drums have different discharge mechanisms and cannot share a “standard error per minute”. Gear pumps are generally more suitable for quantitative delivery when the speed, viscosity, inlet feeding and back pressure are stable; diaphragm pumps and pressure drums are more susceptible to pulsations, air pressure, back pressure, valve state and paint viscosity changes. If there is no flow meter or closed-loop control, the set value of the equipment panel cannot be directly equal to the actual discharge rate per minute. Formal acceptance shall be evaluated for minute repeatability, set accuracy, long-term drift, and batch consistency under fixed paint, temperature, pressure, line, and operating time by weighing method or calibrated flow meter, respectively.
Selection GuideThere will be fluctuations, and there may be voltage drops, but there is no uniform "± how many kV" from the specific model. Labeled 0–100 kV usually represents only the adjustable or rated output range and is not equal to a set value that can be maintained at any load, distance, temperature and continuous operation time. Load pressure drop, current limiting buck or discharge protection may occur during high loads; thermal drift may occur during continuous operation, and abnormal high pressure attenuation may occur due to insufficient heat dissipation, insulation pollution, moisture, cable damage or component aging. The set voltage, actual voltage, output current, temperature, load, alarm and recovery time must be recorded synchronously when judging.
Selection GuideGrounding is the basic condition for whether electrostatic spraying can stabilize adsorption and safe operation. Poor grounding of workpieces, hangers, conveyor chains, metal parts related to spray rooms and operators may cause problems such as poor powdering or painting, over-spraying, unstable film thickness, abnormal corners and dead corners, high-voltage alarms, ignition, discharge, electric shock, dust or solvent environmental safety risks. Before adjusting the voltage, powder gas, atomization gas or paint supply parameters, the grounding path should be confirmed to be reliable. Fixed qualification values or final safety judgments should not be given until specific equipment models, on-site testing methods, grounding resistance data and applicable standard provisions are provided.
Selection GuideIn powder electrostatic spraying, powder volume gas is usually used to drive the venturi powder pump to suck and feed powder, which mainly affects the powder output and delivery stability; atomized gas is also often referred to as auxiliary gas, dilution gas or diffusion gas, which mainly affects the dispersion state of the powder at the muzzle or the end of the powder path, the softness of the powder cloud, and the improvement of pulsation. When adjusting, it is not possible to directly increase the two ways of gas together. It should first be confirmed that the powder fluidization, air source drying, powder pump, powder pipe, nozzle, grounding and high pressure are normal, and then take the allowable range of the manual as the boundary, changing only one variable at a time. When the amount of powder is insufficient, it is preferred to check the powder path and powder gas; when the powder cloud is spitting or reuniting, focus on the atomized gas, powder pump wear and powder tube resistance. Fixed air pressure values should not be given until specific equipment models and powder pump structures are provided.
Selection GuideThe electrostatic spray voltage and current cannot be applied according to a fixed set of values. The voltage mainly affects the charging, electrostatic adsorption and deposition efficiency of the coating particles or powder particles; the current reflects the charge transfer, the proximity of the workpiece, the grounding state, the discharge risk and the electrostatic field strength change. During commissioning, first confirm the equipment type, the allowable range of the instructions, the grounding of the workpiece, the powder or coating status, the nozzle/atomization, and the powder/paint supply stability, and then make a single-variable test spray with the representative workpiece. When the plane adsorption is insufficient, the voltage can be gradually increased after the basic conditions are normal; when deep grooves, inner corners, sharp corners, corner powder, reverse ionization, discharge or high-voltage alarms, priority should be given to reducing the voltage or setting the current limit, rather than continuing to increase the output.
Selection GuideDisk electrostatic disk spraying systems are generally more suitable for liquid electrostatic spraying scenarios with batch stability, large appearance surfaces, high degree of production line continuity, and the desire to improve coating consistency and automation. When selecting the type, you should not only look at the rotating disk body or spray disk parameters, but also evaluate the workpiece structure, paint system, paint supply method, spray room conditions, conveyor line beat, control system, safety interlock, maintenance capacity and test spray results. Fixed speeds, voltages, flows, spraying distances, quotations or payback periods should not be given directly until specific models, paint data, workpiece dimensions, yields and site conditions have been provided.
Selection GuideThe automatic powder electrostatic spray gun is more suitable for factories that already have or plan to build powder spraying lines, especially in scenarios where the workpiece is stable in batch, the product structure is relatively fixed, the beat is clear, the film thickness and appearance consistency requirements are high, the manual spraying fluctuations are large, and it is hoped that rework will be reduced and production replicability will be improved. Not only does it need to "replace the hand gun with an automatic gun", but it also needs to match the spray room, the powder supply system, the recycling system, the conveyor line, the reciprocating machine or robot, the controller, the grounding, the hanger, the curing furnace and the on-site safety management. Before the specific workpiece, output, color change frequency and site conditions are provided, it should not be directly judged that a factory must be suitable, nor should fixed parameters, savings ratio or investment recovery cycle be promised.
Selection GuideBuying an electrostatic spray gun can not only look at the initial offer, because the real impact of the spray gun is the long-term production cost. The unit price of the equipment is only the first cost, followed by powder or paint consumption, one-time pass rate, rework, downtime, wearing parts, maintenance, training, after-sales, spare parts supply, color change cleaning, line compatibility and safety risks. A more reasonable way to evaluate is to calculate the unit qualified workpiece cost or unit qualified area coating cost. In the absence of specific model, workpiece, output, paint price, spare part price and production data, you should not directly write "a certain spray gun saves money" or promise to fix it back to the current cycle.
Selection GuideWater-based paint electrostatic spraying has high viscosity, easy to block, poor atomization, and can not be solved only by "increasing pressure, increasing air volume, or increasing voltage". The water-based paint system, viscosity, solid content, filtration, temperature, resistivity, paint supply method, nozzle specifications, atomization method, grounding and isolation safety should be confirmed first, and then checked in the order of "paint status — filtration - paint supply — nozzle atomization — electrostatic adaptation — cleaning and maintenance". Fixed dilution ratios, pressures, voltages, nozzle calibers or judgments should not be given until specific gun models, paint data and safety configurations have been bound.
Selection GuideWhen selecting electrostatic spray guns in 2026, one cannot simply look at whether the gun can spray, its parameters, or its price. If integration with an MES system and robotic spraying unit is required, the controller communication interface, PLC linkage, recipe management, work order binding, spray gun triggering, alarm data, robot trajectory, gun switching sequence, safety interlocks, access logs, and acceptance criteria must all be evaluated simultaneously. The so-called "seamless integration" cannot be a verbal promise; it must be demonstrated through protocols, point tables, data fields, cycle time, anomaly handling, and on-site FAT/SAT testing. Without providing specific spray gun models, controller versions, robot brands, PLC/MES interfaces, and production line topology, promises of plug-and-play functionality, fixed protocols, remote control capabilities, or automatic closed-loop effects should not be made.
Selection GuideThe value of AI vision and IoT remote monitoring in electrostatic spraying is not to package the spray gun as an "automatic universal device", but to make the spray gun, controller, powder/paint supply, spray room, production line and quality inspection gradually form a perceptible, recordable, early warning, and traceable intelligent unit. AI vision is more suitable for workpiece identification, hanger status identification, spray coverage observation, defect trend analysis, and security behavior assistance identification; IoT remote monitoring is more suitable for equipment status, parameter recording, alarm tracking, maintenance reminders, powder consumption/paint consumption statistics, and remote diagnosis. Until specific models, algorithms, sensors, and platforms are bound, no commitment should be made to recognition accuracy, savings ratios, automatic closed-loop control, or remote modification capabilities.
Selection GuideThe powder on the dead ends should not be simply attributed to "the spray gun is not good enough", nor can it directly promise that the electrostatic cup spray gun will solve all dead ends. Dead corners, deep grooves, inner corners, and recesses in powder spraying are usually affected by the Faraday cage effect, workpiece structure, grounding, powder cloud impact, powder volume, airflow, voltage/current limitation, gun spacing, angle, and spraying sequence. The electrostatic rotating cup spray gun or rotating cup system may have advantages in powder cloud distribution, spray coverage and batch consistency, but whether it is superior to ordinary powder electrostatic spray guns must be verified by the same workpiece, the same powder, the same film thickness target and the same curing conditions. Fixed improvement ratios or absolute win/loss conclusions should not be given until specific model and test data are provided.
Selection GuideThe replacement cycle of nozzles, powder pipes, and pump cartridges cannot be judged only by "how many days used" or "how many hours sprayed". A more reliable method is to combine the spraying effect, powder discharge stability, film thickness fluctuation, powder consumption, wear traces, air leakage and leakage powder with the comparison of new parts of the same model. Before the specific spray gun model, powder pump structure, nozzle specifications, powder pipe material, powder type, output and equipment manual are not provided, fixed replacement days, hours or mandatory scrap standards should not be fabricated.
Selection GuideThe core difference between a manual electrostatic spray gun and an automatic electrostatic spray gun is not "which must be more advanced", but who controls the spraying action. The manual electrostatic spray gun is handheld by the operator to complete the switch gun, gun distance, angle, speed and make-up spray judgment, which is more suitable for small batch, multi-variety, sample, repair and workpiece change scenarios; the automatic electrostatic spray gun is triggered by the controller, PLC, reciprocator, robot or automatic line, which is more suitable for batch stability, clear beat, high appearance consistency requirements, and the need to reduce manual fluctuations. Before selection, confirm whether it is powder spraying or liquid spraying, and then look at the workpiece batch, color change frequency, quality requirements, on-site automation conditions and budget. Fixed voltage, current, air pressure, powder, flow or investment recovery conclusions should not be given directly before the specific model is bound.
Selection GuideThe high-voltage electrostatic tester can assist in judging whether the high-voltage output of the electrostatic spray gun is normal, whether there is leakage, discharge, output decay or instability, but it cannot be judged as "good" or "bad" in a single sentence. The correct approach is to first confirm the equipment model, rated high-voltage range, tester range, test tooling and safety conditions; and then separately check the controller, high-voltage cable, spray gun body, high-voltage package, electrodes, grounding and spraying site conditions. If the test results are lower than the requirements of the manual, the output beats, the voltage drops after loading are obvious, accompanied by abnormal discharges or alarms, it supports further suspicion of abnormal high-voltage links. Before the specific spray gun and tester model are not bound, a fixed qualified voltage value or a general waste criterion should not be given.
Selection GuideThe appearance of orange peel and pinholes in the spray plastic can not be judged as a spray gun problem, nor can it be directly identified as a plastic powder quality problem. Orange peel is more commonly found in film thickness, powder leveling, spray gun powder/airflow/electrostatic parameters, gun spacing, curing, and pretreatment; pinholes are more common in substrate or pretreatment residues, moisture and oil stains, powder moisture, gas release, film thickness does not match curing, compressed air pollution, and other factors. The correct approach is to distinguish the defect form first, and then gradually lock the root cause by "different guns with the same powder, different guns with the same powder, different workpieces with the same gun with the same powder, standard test plate control, single variable test spray".
Selection GuideThe biggest difference between a liquid electrostatic spray gun and a powder electrostatic spray gun is not that "one can spray liquid and one can spray powder", but that the entire process chain is different. The liquid electrostatic spray gun is used for solvent-based, aqueous or other liquid coatings, and forms a wet film by relying on the paint supply system, atomization method and electrostatic adsorption, and then forms a coating by leveling, volatilization, baking or curing; the powder electrostatic spray gun is used for thermosetting or thermoplastic powder coatings, and completes powder deposition by relying on bucket fluidization, powder pump transportation, powder charging and workpiece grounding, and then forms a coating by baking and melting, leveling and curing. The two are different in terms of equipment structure, feeding system, spraying parameters, safety requirements, cleaning and maintenance, cost accounting and applicable workpieces, and cannot replace each other or mix core components across models.
Selection GuideThe low cost of small sample powder spraying in the laboratory is not to make the equipment as simple as possible, nor to arbitrarily reduce the amount of powder, voltage or curing conditions, but to reduce the powder loss, color change cleaning time, sample rework and invalid repeat tests in a single test under the premise of meeting the safety, film thickness, appearance and test purposes. The special powder electrostatic spray gun for laboratory is more suitable for powder formulation verification, color proofing, sample confirmation, small piece test spraying, process window exploration and customer sample test. Fixed voltage, air pressure, powder volume, gun spacing or cost saving ratio should not be given until the specific gun model, powder cup/bucket structure, powder type, specimen size, target film thickness and laboratory safety configuration have been confirmed.
Selection GuideThe industrial electrostatic rotating cup spray gun is suitable for large batches of paint spraying. The core reason is not that "any scene is better than an air spray gun", but in continuous production, it can achieve high coating efficiency, stable film thickness consistency and better paint utilization management through high-speed rotational atomization, electrostatic adsorption, stable paint supply and automatic trajectory control. It is more suitable for automotive parts, home appliance shells, metal products, construction machinery parts, profiles, plates and other batch, repetitive, articulated spraying scenarios. Scenarios with small batches, frequent multi-color switching, many complex dead corners, on-site safety and insufficient paint supply conditions should not simply use the spinning cup as the default first choice. Fixed speed, flow, high pressure or forming gas parameters should not be given until the specific rotating cup model, paint system, workpiece structure and production line conditions have been confirmed.
Selection GuideThe powder electrostatic spray gun can not be adjusted to increase the voltage, increase the amount of powder or pursue the "big powder fog" according to the feeling. The more secure order is: first confirm the safety, grounding, air source, powder fluidization and powder discharge stability; then gradually adjust the powder volume, conveying gas, atomization gas, voltage, current limit, gun distance, angle, gun speed or automatic line beat according to the workpiece structure, target film thickness and appearance requirements; finally verify with film thickness, appearance, powder consumption, rework rate and a qualified rate. A common set of fixed parameters should not be given until the specific gun model, controller version, powder type and workpiece structure are bound.
Selection GuideThe point of metal powder spraying is not to open up the powder mist, but to keep the metal effect, film thickness and color consistent. The site should first confirm the powder type, sample standard and customer appearance requirements, and then control the powder fluidization, spray gun powder volume, conveying air/atomized gas, electrostatic parameters, gun spacing, angle, gun speed, pendant direction, curing conditions and recycled powder ratio. Metal powders are more prone to problems such as color difference, flowering, cloud spots, corners shining, uneven metallicity, and color drift of recycled powder than ordinary solid powder. Fixed spraying parameters should not be applied directly before the powder grade, gun model, workpiece structure, target film thickness and prototype are confirmed.
Selection GuideFluorocarbon powder spraying wants to achieve the highest cost performance, not to buy the powder at the lowest price, nor to press the film thickness to the minimum, but to reduce the unit qualified area cost under the premise of meeting the customer's weather resistance, appearance, film thickness, adhesion and curing requirements. The site should focus on six things: selecting the right powder system and application grade; stabilizing the pretreatment; establishing a film thickness window with representative workpieces; adjusting the amount of powder, airflow, electrostatic parameters and gun distance to "uniform deposition" instead of "large powder fog"; managing the ratio of new powder to recycled powder, sieve powder and color change loss; and verifying the cost with the curing curve and the first pass rate. Fixed spraying parameters or savings should not be given until powder grade, target film thickness, workpiece material, curing conditions and customer standards have been confirmed
Selection GuidePowder spraying shows orange peel marks, which should not only be blamed on the spray gun, but also on the poor quality of the plastic powder. The orange peel pattern is usually associated with film thickness, powder leveling performance, spray gun powder output, delivery gas/atomization gas, voltage current, gun spacing, gun speed, workpiece temperature, curing conditions, pretreatment, and powder batches. The site should first confirm whether the orange peel is an "unexpected defect" or a decorative effect required by the texture powder, sand grain powder, and wrinkle powder itself selected by the customer; then check in the order of "film thickness — powder — spray gun parameters — curing — pretreatment — site environment". It is not recommended to give fixed voltage, air pressure, temperature or time values before confirming the powder grade, target film thickness, curing curve and workpiece structure.
Selection GuideEnglish summary is being prepared. The full article is available in Chinese.
